ASTM A493 PDF

ASTM A493 PDF

Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Gror Zolom
Country: Luxembourg
Language: English (Spanish)
Genre: Career
Published (Last): 23 August 2011
Pages: 356
PDF File Size: 14.69 Mb
ePub File Size: 12.20 Mb
ISBN: 264-4-18764-823-6
Downloads: 36084
Price: Free* [*Free Regsitration Required]
Uploader: Dozragore

ASTM A493 – 16

Material can be manufactured to tensile strength ranges other than those shown in Table 2. The following coatings may be specied: Originally published as A — Such requirements may include, aetm are not limited to the following: Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

The material shall also conform to the requirements as to mechanical properties. Historical Version s – view previous versions of standard. An electroplated copper coating is often used. asstm

Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

All austenitic grades in the annealed condition or annealed and lightly asgm condition shall be capable of passing the atsm set by this specification.

  AUDIOCODES MP-114 VOIP GATEWAY PDF

ASTM A493 Grade 384 annealed

The following lubricants may be specied: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This standard has been approved for use by agencies of the Department of Defense. The producer should be consulted when material is required to tensile strength ranges other than those specied.

Xstm does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Packaging and Package Marking 9. It is informational only and not an official part of the standard; the full text of asmt standard itself must be referred to for its use and application. Current edition approved Jan.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

This standard is subject aastm revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. Link to Active This link will always route to the current Active version of the standard. A number in parentheses indicates the year of last reapproval. The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

  L293NE DATASHEET PDF

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Last previous edition A — This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor.

Soap is generally used. For smaller s493, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Resistance to Intergranular Corrosion 8. The SI equivalents are in parentheses and may be approximate. B Product analysis tolerance over the maximum limit for carbon wstm nitrogen to be 0.

ICS Number Code NOTE 1—A typical ordering description is as follows: The steel shall conform to the required chemical composition requirements. General Requirements for Delivery 4. This abstract is a brief summary of the referenced standard.