ASTM E466 PDF

ASTM E466 PDF

Download scientific diagram | Typical sample for fatigue test according to ASTM E Standard. from publication: Effect of Hot Isostatic Pressure treatment on. ASTM E , Standard practice for conducting force controlled ASTM E , Standard terminology relating to fatigue and fracture testing 1). ASTM E covers axial force controlled fatigue tests of metallic materials in the fatigue regime where strains are predominately elastic, both at initial loading.

Author: Taukus Mazuhn
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: Medical
Published (Last): 18 August 2016
Pages: 492
PDF File Size: 5.50 Mb
ePub File Size: 6.61 Mb
ISBN: 406-9-60537-254-6
Downloads: 32756
Price: Free* [*Free Regsitration Required]
Uploader: Grosar

ASTM E46 conducts axial fatigue tests to obtain the fatigue strength of metallic materials in the fatigue regime where the strains are predominately elastic both upon initial loading and throughout the test. For example, specimen alignment is of utmost importance and the procedure outlined in Practice E would be advantageous.

In view of this, no maximum ratio of area grip to test section should apply.

ASTM E Load Controlled Constant Amplitude Fatigue Tests of Metals

Since however, the environment can greatly in? The area restrictions should be the same s466 for the specimen described in 5. Also, Refsalthough they pertain to straincontrolled testing, may prove of interest since they deal with sheet specimens approximately 0. ASTM E covers axial force controlled fatigue tests of metallic materials in the qstm regime where strains are predominately elastic, both at initial loading and throughout the test.

To ensure test section failure, the grip cross-sectional area should be at least 1. To do so would require the control or balance of what are often deemed nuisance variables; for example, hardness, cleanliness, grain size, composition, directionality, surface residual stress, surface? Testing Procedure Place the xstm securely in the grips of the testing machine.

This practice is limited to the fatigue testing of axial unnotched and notched specimens subjected to a constant amplitude, periodic forcing function in air at room temperature. The test section length should be approximately two to three times the test section diameter.

  ABRAMELIN EL MAGO PDF

To do so f466 require the control or balance of what are often deemed nuisance variables; for example, hardness, cleanliness, grain size, composition, directionality, surface residual stress, surface finish, and so forth. Continue sinusoidal cycles to failure.

The value of 1. Otherwise, the same dimensional relationships should apply, as in the case of the specimens described in 5. Static and fatigue forces up to 25 kN 5, lbf Frequency ratings up to Hz Servohydraulic Small, portable footprint.

ASTM E466 Load Controlled Constant Amplitude Fatigue Tests of Metals

Record the load at the time of failure. The results may ee466 be used as a guide for the selection of metallic materials for service under conditions of repeated direct stress.

One set of strain gages should be placed at the center of the gage length to detect misalignment that causes relative rotation of satm specimen ends about axes perpendicular to the specimen axis. As a cautionary note, should localized yielding occur, signi? A number in parentheses indicates the year of last reapproval.

Threaded end specimens may prove difficult to align and failure often initiates at these stress concentrations when testing in the life regime of interest in this practice. Improper methods of preparation can greatly bias the test results. This knowledge and care provides the most meaningful and best possible high cycle fatigue life results. For cylindrical specimens, alignment should be checked by means of a trial test specimen with longitudinal strain gages placed at four equidistant locations around the minimum diameter.

Failure may be de? For rectangular cross section specimens, alignment should be checked by placing longitudinal strain gages on either side of the trial specimen at the minimum width location. All material variables, testing information, and procedures used should be reported so that correlation and reproducibility of results may be attempted in a fashion that is considered reasonably good current test practice. It is advisable to determine these surface residual stresses with X-ray diffraction peak shift or similar techniques, and that the value of the surface residual stress be reported along with the direction of determination that is, longitudinal, transverse, radial, and so forth.

  BORIS PAHOR NECROPOLIS PDF

Specimens can be round or flat.

NOTE 2—Measurements of dimensions presume smooth surface? The test forces should zstm monitored continuously in the early stage of the test and periodically, thereafter, to ensure that the desired force cycle is maintained.

e66 Current edition approved Nov. The size of the gripped end relative to the gage section, and the blend radius from gage section into the grip section, may cause premature failure particularly if fretting occurs in the grip section or if the radius is too small.

Originally approved in Give our test engineers a call today for help configuring the best test machine and accessories according to ASTM E We are confident that we have what you are looking for.

This practice is limited to the fatigue testing of axial unnotched and notched specimens subjected to a constant amplitude, periodic forcing function in air at room temperature. The reduced section length should be greater than three times the minimum test section diameter.

ASTM E466 – Force Controller Constant Amplitude Axial Fatigue Testing of Metallic Materials

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Touchstone Research Satm, Ltd. Ra, in the longitudinal direction. Surfaces intended to be parallel and straight should be in a manner consistent with 8. In the typical regime of 10? Since specimen preparation can strongly in? In view of this fact, the method of preparation should be agreed upon prior to the beginning of the test program by both the originator and the user of the fatigue data to be generated.

The test section length should be approximately two to three times the test section width of the specimen. Permission rights to photocopy the standard may also be secured from the ASTM website www.