DS2490 DATASHEET PDF

DS2490 DATASHEET PDF

table in the DSx 1-Wire network cables data sheet. Both adapters are based on the DS USB-to-. 1-Wire bridge chip. Free software drivers for. Both adapters are based on the DS USB-to-. 1-Wire bridge chip. See the DS data sheet for the conditions where SUSO is active. Revision C of the. DS Usb to 1-Wire Bridge Chip. FEATURES. Communicates at regular and overdrive 1Wire® speeds Supports 12V EPROM programming and stiff 5V.

Author: Vilmaran Juzil
Country: Croatia
Language: English (Spanish)
Genre: Environment
Published (Last): 10 February 2015
Pages: 309
PDF File Size: 16.4 Mb
ePub File Size: 16.49 Mb
ISBN: 854-5-65900-736-3
Downloads: 78380
Price: Free* [*Free Regsitration Required]
Uploader: Mukazahn

Thank you in advance and sorry for my bad english! Althought the bus is planed with a length of about 50 meters and devices there is only one 18S20P for testing at the moment.

OWFS Developers – Usb problem with DS

It’s done in the same manner with the ds In both chipsbyte is completed. The reason may be that absurd USB “devices” like this http: The section of the DSR datasheet you quoted above says it “applies strong pullup to 5V”, and that would be parallel to the ones between the IO pins and the HV pin. Anything that can go wr fortune: Klaus This SF. And due to your recommends i increased the Capacitors now.

Free forum by Nabble. The peripheral function is a USB to 1.

  LEY 11683 ACTUALIZADA PDF

(PDF) DS2490 Datasheet download

In the meantime i’ve tried to increase the capacitors in the 5V Power supply line and after the 3,3V Regulator which might be indeed a little bit small. But i would prefer to do it without the hub. You could use an The effect of the slew rate control is shown in Figure 4. Segmentation violation — Core dumped This SF. The slope is determined by the load on the bus and the value of the pullup currentDSinitiated datasneet edges.

You have to limit the current flowing into empty capacitors by applying a resistor or better a choke coil to the supply lines.

Empty capacitors are like short circuits. If i dis- and reconnect the DS without reloading the module the following happens: Probably the usb port of the hub is less picky with some electrical parameters than the notebook itself? Hm, at the weekend i will have access to some testing equipment and then i will check this. Revision C ofproduction tested. If this is not sufficient i guess i datashest need a choke coil instead which is larger than the whole circuit itself: But this makes no improvement which would surprised me.

In case a device has a failure, the usb driver can turn off the power for the specific port. Of course the peripheral device may be in some sort oft sleep mode until it’s initialized by a driver. The 8-channel version of the DS makes it easy to split a larger application into smaller networks with fewer 1-Wire devices on each line. DS19xx pdt Text: That’s why you need an LC or RC circuit, not a capacitor alone.

  LOS DOCE CESARES SUETONIO PDF

Kernel is a plain 2. In both chips theis completed. So the Capacitors have to be loaded only if i plug in the device. Particularly i would like to have an explanation for this behaviour.

DS 12Mbps 0x DS 0x 0x 0x 0x 0x 0x The effect of the slew ratecontrolled by the DS Yes that’s how i expected. Usb problem with DS If the power supply would be switched the choke coils would make bad things too. Wouldn’t this be a chicken and egg problem? I’m doing my first experiments with owfs and a few one-wire devices.

It may be a related issue, though.

The shape of sd2490 uncontrolled. The term “5v logic” implies specific voltages for high and low values, which the DSR apparently doesn’t obey. Best wishes, Klaus This SF. Your fuse protects the onewire cable, not the interface circuit. But i can’t imagine that this usb-port which is capable of mA should have a problem with a few mA.