HITEC ECLIPSE 7 MANUAL PDF

HITEC ECLIPSE 7 MANUAL PDF

Hitec ECLIPSE 7 Pdf User Manuals. View online or download Hitec ECLIPSE 7 Owner’s Manual. View and Download HITEC Eclipse 7 Pro user manual online. 7 Channel GHz Aircraft Radio Control System. Eclipse 7 Pro Remote Control pdf manual. Does anyone have a copy of the manual for the Eclipse 7 that is not missing pages 44 and 45, every PDF I have found goes pg 42,43,4,5,46,

Author: Yonos Akinok
Country: Burma
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 1 August 2016
Pages: 383
PDF File Size: 19.94 Mb
ePub File Size: 9.99 Mb
ISBN: 501-9-68789-501-2
Downloads: 6491
Price: Free* [*Free Regsitration Required]
Uploader: Grozshura

These functions are used to select the model memory, the model type from airplanes, gliders, and helicoptersset the Timer, and other useful functions. Helicopter Setup Instructions The following example shows how the Eclipse 7 Pro may be programmed for a helicopter model. Page 9 If the instructor’s transmitter is on a different frequency than the student’s, use the student’s transmitter as the master transmitter, and the other transmitter as the student’s. Switch power back on. Remember, you can input separate, independent throttle curve settings for each flight condition!

Helicopter Setup Instructions You begin at set point 1, idle. EN V1. And then, press Cursor three times to get next step. Turning Off -Turn off the receiver, then turn off the transmitter.

Heading change opposite to roll command i.

Manual do usuário HITEC ECLIPSE 7 – Baixe o seu guia ou manual de usuário HITEC ECLIPSE 7

Please note that for best results, trimming should be done in near-calm conditions. Set-up Use of the Hitec 2.

Page 48 Competition Glider Quick Setup Instructions and down travel for each flap, which is handy for models the F A offset see previous step. Telemetry system Information When you first turn on your transmitter, the first screen shown below appears on the LCD display.

  AZIM PREMJI BIOGRAPHY PDF

It is ideal to The amount of aileron and elevator response can be make slow-flying scale models fly realistically. Eclipse 7 Helicopter heli Programming Helicopter Setup Instructions The following example shows how the Eclipse 7 Pro may be programmed for a helicopter model. For example, you might have a scale model which is very sluggish at lower speeds such as takeoff and landing yet is very sensitive at higher speeds. Cond switches to their proper position. Optic 6 Sport 2.

Hovering Pitch Adjustment Knob Aircraft acro Menu Functions Model Setup Functions Page 8 Optic 6 Sport 2. Glider Model Function Descriptions inboard ailerons are programmed to move a smaller back of transmitter to angle. Operating With A Trainer Cord Aileron Dual Rate setting.

If any changes are made, go back through the previous steps and verify that they are not also affected.

A wing that generates lift also generates a drag component called induced drag, meaning that drag is induced as a by-product of the lifting wing. Notes On Servos Release the link button. It is commonly used during autorotation, and activated with the Flt. Transmitter Input Buttons You’ll learn how to use these buttons in the setup sections that follow 6.

Eclipsf controls, then half-roll the model. You set them up in the Model Setup menus see page?? The Hitec cord is specifically marked at one end as the “master” Charge Jack Trainer Jack the other end as “student”. Mode switch turns this function on and off fully back turns it ON.

Hitec Eclipse 7 Manual

Before you decide to make a change, be sure to try the test several times before making adjustments. The transmitter may be programmed for airplanes, gliders, or helicopters, all with special mixing functions, so it can accommodate virtually any model configuration. Also See for Eclipse 7 Pro User manual – 16 pages.

  CONFABULARIO TOTAL JUAN JOSE ARREOLA PDF

NOR is intended for hovering flight. Model Setup Functions Model Name The Model Name function is used to create an alphanumeric name which is stored in the model memory along with the rest of the model settings.

bitec

In the case of a glider, you have to specify whether it has two 2WNG or four 4WNG wing servos most slope gliders use two wing servos, and competition gliders use four wing servos, two each for outboard and inboard ailerons and flaps. Page 3 Collapse the mnual antenna, and fully extend the instructor’s antenna.

Model Setup Functions Charge the Batteries! Once the power-down mode is activated it runs for about 90 seconds, effectively shortening the range to 30 meters, or feet. Page 24 Model Msnual Functions Model Name The Model Name function is used to create an alphanumeric name which is stored in the model memory along with the rest of the model settings.

Glider Model Function Descriptions your sailplane. So the traditional method of range check, lowering the transmitter antenna, is not applied. Connect the transmitter charging cord into the charging socket on the bitec of the case, left side and airborne Ni-MH batteries to the receiver connector on the charger.

Transmitter Input Buttons The buttons are used for different things as follows: We encourage you to review this information before using these products.

Sub-trims [ Strm]